[ + ]
Biscuits
Biscuits are support mechanisms used in joining wood. They are created in various sizes for different applications, and are usually used with a power tool called a plate joiner or biscuit cutter.
[ + ]
Checkering
Checkering is a decorative technique in which a criss-cross pattern is applied to wood. It is used most often on gunstocks, for better grip.
[ + ]
Checking
Checking is the splitting and cracking that occurs as wood dries. Checking can be avoided by regulating the environment in which the wood is dried to slow down the rate of speed in which moisture evaporates.
[ + ]
Creep
Creep is the result of substrates or layers reacting to their individual rates of drying, temperature, and relative humidity. The different reactions cause the pieces to expand, contract, move or shift over time.
[ + ]
Dovetail Joints
A dovetail joint is joining technique. A popular solution for right angle applications, such as drawer corners, a dovetail joint is a series of pins cut to extend from the end of one board. The pin cuts lock into a series of tails cut into the end of another board. The pins and tails have a trapezoidal shape. Once glued, no mechanical fasteners are required; the joint is permanent.
[ + ]
Edge-to-Edge Gluing
The process of gluing boards edge to edge to create a wider panel than can be achieved with one board.
[ + ]
Edge-to-End Gluing
The process of gluing boards edge to end.
[ + ]
End-to-End Gluing
The process of gluing boards end to end. This technique is used infrequently, since the end grains of boards present additional difficulties for successful bonding and a seamless appearance. In addition, the length of boards is less often an issue, as trees grow much taller than wider.
[ + ]
Fiberized Surface
A fiberized surface occurs when wood has been improperly sanded against the grain, by using rough or dull planer blades or by using abrasives that are too coarse. The result is a surface that is rough or fuzzy.
[ + ]
Finger Joints
A joining technique. Often used in commercial processing of softwoods to join ends and avoid the inherent difficulties of end joining. It is also a great way for producers to reduce waste or scrap.
[ + ]
Injecting Glue
A technique for applying glue. Most often used in repair and restoration, glue is injected into small crack or loose joints with the use of a small glue syringe.
[ + ]
Moisture Meter
A moisture meter measures the moisture content of wood. When using adhesives, wood with a moisture content of 4-7% for hardwoods and 6-8% for softwoods is recommended.
[ + ]
Open-grained Wood vs. Closed-grain Wood
Generally, open grain woods are softer woods and more porous. Closed grain woods are harder woods and less porous.
[ + ]
Polyvinyl Acetate (PVA)
PVA's have been around since the 1940s, and are commonly known as white glues.
Gorilla Wood Glue is a cross-linked PVA. White glues are not cross-linked, meaning that the polymers are not joined together as a web. This cross-linking gives the glue enhanced strength, as well as better heat and moisture-resistance than white glue.
[ + ]
Radio Frequency Press
Most often used in commercial application, a radio frequency is used to speed the cure rate of water-based adhesives by removing the moisture or water from the glue. It is also used in some cases for kiln drying of lumber.
[ + ]
Snipe
Snipe is the gouging or depression of a board as a result of running it through a planer. Snipe can occur at either end of the board when it enters the planer's out-feed roller or in-feed roller.
On a joiner, snipe can occur due to improper table alignment and improper feeding.
[ + ]
Stepped Joints
Stepped joints occur when two adjacent laminates change dimension differently because of grain orientation and/or moisture. The adhesive cannot resist this change and the laminates slightly shift. The joint will appear “stepped”.
[ + ]
Sunken Joints
Sunken joints are slight depressions at the glue lines in a finished panel. Sunken joints result from the wood around the joint expanding when it comes in contact with the moisture from adhesive.
To avoid sunken joints, wait for the wood swelling to go down before planing or sanding.
[ + ]
Woodturning
Woodturning is the process of shaping wood using a lathe. Woodturning is used to create round items like bowls, spindles, table legs, wooden baseball bats and others.